• Tuesday, October 26, 2021
  • 09:15 - 18:00
  • Memo
  • Tiglio Room A6 Pav
  • Italian

Organized by: Ecomondo Scientific Technical Committee, Italian Chemical Society – Division Environmental and Cultural Heritage Chemistry, ATIA – ISWA

CALL FOR PAPERS

The aim of a decoupling between the advisable economic development and the undesirable depletion of planet resources requires a huge effort towards a technical improvement, able to implement new processes to close the cycles in all productive value chains.
A first important European initiative, in line with the new Circular Economy Action Plan, has recently been delivered, in relation to batteries (industrial, automotive, electric vehicle and portable), but the ambitious targets fixed by EU for the next years cover many priority sectors (plastics, packaging, WEEE, textiles, building and construction, food).
This seminar thus intends to show some advanced initiatives of technological innovations which could be applied to different categories of residues, by-products or discards, both industrial and urban, with the aim of improving resources circularity and valorisation.

Section Chairs

Fabrizio Passarini, Ecomondo Scientific Technical Committee, University of Bologna
Mario Malinconico, Ecomondo Scientific Technical Committee, ATIA – ISWA, CNR
Mauro Majone, Ecomondo Scientific Technical Committee, University “La Sapienza” Rome

Programme

9.20-9.30 Introduction by the Chairs and a short summary on the papers presented through posters

9.30-10.30 Invited lectures

9.30-9.45 Giacomo Rispoli (MyRechemical, Gruppo NextChem - Maire Tecnimont)
The waste to chemical technology for the prodoction of intermediates and “circular” fuels from waste


9.45-10.00 The frontiers of plastic mix chemical recycling
Antonio Protopapa, COREPLA

10.00-10.15 A framework of present possibilities and perspectives of carbon recovery from waste flows
Paolo Pavan, Università “Ca Foscari” di Venezia

10.15-10.30 Recycling processes for end of life face masks: hypotheses for a sustainable value chain
Letizia Tuccinardi, ENEA

10.30-13.00 Presentations selected from the Call for papers

10.30-10.45 Cailotto A., Mantovani M., Zanetti N., Della Zassa M. (KINN-Tech s.r.l., Spin Off of the University of Padova, www.k-inntech.it), Canu P. (Industrial Engineering Department, University of Padova, Via Marzolo 9, 35131, Padova)
Inertisation treatments of waste metallic powders

10.45-11.00 Antonio Castorini, Tiziano Canali, Paride Festa Rovera (TBF+Partner AG)
The recovery of metals from the fly ash of waste-to-energy plants

11.00-11.15 Daniele Ricci, Matteo Carfagno, Matteo Maiello, Paolo Magaldi (Magaldi Power S.p.A., Salerno)
Magaldi Ecobelt® WA On site valorization treatment of dry IBA as a revenue opportunity for WtE plants

11.15-11.30 Francine Duarte Castro, Mentore Vaccari (University of Brescia, Italy), Laura Cutaia (ENEA, Italy)
An experimental design approach for recovering materials from automotive lithium-ion batteries

11.30-11.45 Marco Molica Colella, Vittoria Novelli (CiaoTech S.r.l.)
Development of an Efficient Microwave System for Material Transformation in energy INtensive processes for an improved Yield

11.45-12.00 Loretta Venturini, Fabrizio Meroni (Iterchimica S.r.l.)
The valorization of waste plastics in durable asphalt concrete: the Genova San Giorgio Bridge

12.00-12.15 Martino Colonna, Lorenzo Crosetta, Alessandro Nanni (DICAM-UNIBO), Massino Rinaldi (Warrant Hub)
Complete recycling of end-of-life sport equipment: the LIFE RE-SKIBOOT Project

12.15-12.30 Nicola Fiorotto (R&D Network and Innovative Platforms Head, Versalis
Versalis: Hoop® a sustainable recycling of mixed plastics project

12.30-12.45 Rosa Turco, Riccardo Tesser, Martino Di Serio (Department of Chemical Sciences, University of Naples Federico II), Salvatore Mallardo, Mario Malinconico (Institute for Polymers, Composites and Biomaterials - IPCB, National Council of Research - CNR))
Recycling Expanded Polystyrene (EPS): Giving a new life to a waste

12.45-13.00 Marlene Scalise (ass. culturale Riscarti), Flavio Ottaviani (Energy manager)
“Riscarti festival” and the sustainability culture

13.00-14.00 Break

14.00-14.15 Elena Rubino, Marco Botta, Gianluca D'Aquila (Eni Rewind)
Sustainable technological innovations for the recycling and recovery of materials and energy

14.15-14.30 Silvia Codelupi (COOPBOX GROUP S.P.A)
GLOPACK project: from biomass recovery to food packaging

14.30-14.45 Luisa Di Paola (Faculty of Engineering, Università Campus Biomedico di Roma)
REWINE: a biorefinery platform based on winery wastes

14.45-15.00 G. Metelli, R. Pagliarello (Università della Tuscia), M. Garegnani (Politecnico di Milano, DAER), L. Nardi, A. Desiderio, M. Calvitti, E. Benvenuto, E. Lampazzi (ENEA, Biotechnology and Agro-Industry Division)
A lab scale insect-based microgreens waste recovery system

15.00-15.15 Coos Wessels (CirTec)
Optimisation of sewage treatment by recovery of cellulose

15.15-15.30 Giovanni Luca Russo, Maria Oliviero, Marco Baselice, Antonio Luca Langellotti, Paolo Masi, Raffaele Sacchi (Department of Agricultural Sciences & CAISIAL center, University of Naples Federico II, Italy), Vito Verardo (Department of Nutrition and Food Science, University of Granada, Spain)
Bioconversion of agri-food waste in high added value molecules through microalgae cultivation

15.30-15.45 Rachele Malesani, Alberto Pivato (DICEA, Department of Civil, Architectural and Environmental Engineering, University of Padova), Andrea Schievano (Department of Environmental Science and Policy, University of Milan)
Compost Heat Recovery Systems as alternative plants to provide domestic heating from residual biomasses

15.45-16.00 Marazza, D. (Università di Bologna), Contin, A., Hornung, A., Daschner, R., Eder, S., Ouadi, M., Jahangiri, H., Graute, L., Zhou, J., Lieftink, D., Grassi, A., Capaccioli, S., Righi, S., Lama V., Rapone, I., Langley, M., Tuck, C., Claret Carles
To-Syn-Fuel: renewable liquid fuels and hydrogen from sewage sludge in a 500 kg/h real plant

16.00-16.15 Lorini L., Villano M., Majone M. (Department of Chemistry, University of Rome La Sapienza), Valentino F. (Department of Environmental Science, Informatics and Statistics, Ca' Foscari University of Venice), Battista F., Monarin G., Rizzoli F., Bolzonella D. (Department of Biotechnology, University of Verona)
Degradability of waste derived bioplastics: assessment and evaluation of BMP

16.15-16.30 Giovanni Gadaleta, Sabino De Gisi, Giusy Santomasi, Francesco Todaro, Michele Notarnicola (Dipartimento di Ingegneria Civile, Ambientale, del Territorio, Edile e di Chimica, Politecnico di Bari, Italy)
Influence of cellulose acetate as a bio-plastic on the yield of combined anaerobic digestion and composting treatment

16.30-16.45 Massimo Mari, Antonella Macagnano (CNR - Istituto sull'inquinamento atmosferico), Fabrizio De Cesare (Università della Tuscia - DIBAF), Carla Mazziotti (CNR - Dipartimento di Ingegneria ICT e Tecnologie per l'Energia e i Trasporti)
Electrospinning technology for eco-design in planning through the recovery of agro-food waste

16.45-17.00 Valentina Beghetto, Riccardo Samiolo (Crossing Srl)
Antimicrobial Waterproof Recyclable Environmentally Sustainable Clothes

17.00-17.15 Nelson Marmiroli (Consorzio CINSA, Parma, Italy), Matteo Cauli, Marco Ruggi (Ri.Circola Srl, Milan, Italy), Lucia Toffanin; (INDICAM, Milan, Italy)
Sustainable solutions for the disposal of seized, counterfeit goods: solutions for recycling

17.15-17.30 Discussion and closure

Poster Session

WMV1-P1 STEPPER SCREEN: il nuovo brevetto di PAL per vagliare il rifiuto / Tommaso Zanasi (PAL srl)

WMV1-P2 Come la regolazione Arera può influenzare la qualità dei servizi di gestione integrata dei rifiuti / Giorgio Ghiringhelli (ARS ambiente Srl e Università Cattaneo – LIUC), Carlo Sguario, Paolo Pagani, Monica Benzi, Giuseppe Sbarbaro (UTILITEAM Srl)

WMV1-P3 VOW - Valorising Organic Waste / Stefano Santini (Nest srl)

WMV1-P4 New sizing strategies to improve recovered carbon fibres reinforcement on polymer composite / Miquel Royo, Marc Martín, Luis Granda, Diego Morillo, Ruth Garcia, Núria Portolés (LEITAT Technological Center)

WMV1-P5 Il recupero dell'Olio da Disoleatore / Elisabetta Piana (Karberg & Henenmann srl)

WMV1-P6 Circular economy design da waste ad opportunità aziendale / Dr. Alberto Claudio Tremolada (Competence center manufacturing & exhibitions manager Adaci - Associazione It. Acquisti e Supply Management)

WMV1-P7 FLIES4VALUE - Insetti per la bioconversione di sottoprodotti agroalimentari / Lara Maistrello (BIOGEST-SITEIA UNIMORE), Lorenzo Bertin (CIRI AGRO UNIBO), Maria Grazia Tommasini (CRPV Soc. Coop.), Federica Rossi (Proambiente S.C.r.l.), Augusta Caligiani (SITEIA.PARMA UNIPR)

WMV1-P8 Tenebrio molitor: innovative tool for food loss and waste valorisation and biopolymers recovery/ Simona Errico, Anna Spagnoletta, Stefania Moliterni, Salvatore Dimatteo, Alessandra Verardi, Paola Sangiorgio, Ferdinando Baldacchino, Roberto Balducchi (ENEA - Centro Ricerche Trisaia)

WMV1-P9 New biochar-based composite for phosphorous recovery from wastewater / Carlotta Carlini, Alessia Alcantarini, Nicolas Greggio, Antonio Primante, Andrea Contin, Diego Marazza (CIRSA - Interdipartimental Research Centre for Environmental Science, Alma Mater Studiorum – Università di Bologna)

WMV1-P10 REE, critical raw material and geopolymers recovery from fly ashes / Paolo Plescia (Resilco Srl), Ivana Moscato (B1Shop Srl), David Callejo Munoz (Resilco Srl)

WMV1-P11 Plastic waste pretreatment for chemical recycling / Paolo Plescia (Resilco Srl), Ivana Moscato (B1Shop Srl), David Callejo Munoz (Resilco Srl)

WMV1-P12 GLycerol to Aviation and Marine prOducts with sUstainable Recycling / Patrizia Circelli (Ciaotech srl)

WMV1-P13 Estrazione di metalli da ceneri pesanti di termovalorizzazione di rifiuti urbani./ Carlo Limonti, Giulia Maria Curcio (Università della Calabria, Rende, Cosenza), Roberta Caruso, Francesco Marchio, Alessio Siciliano (Econet srl, Lamezia Terme, CZ)

WMV1-P14 Mercati locali di qualità e applicazioni di economia circolare/ Marino Cavallo (Città Metropolitana di Bologna)

WMV1-P15 Il recupero di rifiuti plastici con processo di pirolisi in Italia: Aspetti tecnici e normativi / Dott. Federico Pelizzari (Green Evolution S.r.l. Società Benefit), Prof. Ing. Gianclaudio Faussone (Politecnico di Torino)

WMV1-P16 FRELP BY SUN (Full Recovery End of Life Photovoltaic BY the energy from the SUN) / Lodovico Ramon (R&D Manager TIALPI SRL)

WMV1-P17 Gruppo CAP: Innovazioni tecnologiche sostenibili nel servizio idrico integrato / Desdemona Oliva (Gruppo CAP)

WMV1-P18 Nuove tecnologie di trattamento del sottovaglio da selezione dei RUR per recupero di materia / Domenico Ruggiero (S.A.P.NA. SpA - Sistema Ambiente Provincia di Napoli)

WMV1-P19 Soluzioni innovative per la gestione di impianti di confinamento e di percolati complessi: il caso di Progeco Ambiente SpA che sfrutta geofisica e fitodepurazione / Breda S., Zanoli A., Cantale V., Scanferla P., Argese E. (Fondazione Università Ca’ Foscari di Venezia), Finotti Francesco, Finotti Franco, Tonelli A. (Geotila srl), Giovane G., Bonacina G. (Progeco Ambiente SpA), Castellaro C. (Moho srl), Criscione P. (Desam srl)

WMV1-P20 Sustainable food packaging from agro-waste: from Nature for Nature / Annamaria Celli, Laura Sisti, Micaela Vannini (DICAM, University of Bologna), Giuseppe Vignali (Department of Engineering and Architecture, University of Parma), Silvia Folloni (Open Fields Srl., Colorno, PR).

WMV1-P21 COMPOSER project - Innovative composite material for sustainable Circular Economy models / Marco Diani, Eleonora Manarin, Gianmarco Enrico Griffini, Marcello Colledani (Politecnico di Milano)

WMV1-P22 Evaluation of emissions generated from combustion of compost and lignocellulosic biomass/ Francesco Gallucci, Enrico Paris, Monica Carnevale, Adriano Palma, Beatrice Vincenti (Council for Agricultural Research and Economics, CREA-IT), Raffaele Mancini, Marco Calcopietro (Aster Energetica Srl), Ettore Guerriero (CNR-IIA)

WMV1-P23 Nuove soluzioni per l'economia circolare: riduzione volumetrica e valorizzazione carbon-negative / Luigi Iannitti (Chief Innovation Officer - RESET Srl), Anna Curatolo (R&D Engineer - RESET Srl), Andrea De Silvestri (R&D Engineer - RESET Srl)

WMV1-P24 L’impatto ambientale prodotto dal Covid-19 / Mangiagli Sebastiano (Istituto di Istruzione Superiore “A. Ruiz”, Augusta)

WMV1-P25 Materials recovery from EoL mobile phones: the portent project / Danilo Fontana, Massimiliana Pietrantonio, Stefano Pucciarmati, Federica Forte (ENEA, Department for Sustainability, Via Anguillarese 301, 00123, Rome, Italy)

WMV1-P26 Plant cell cultures for bioconversion of industrial food waste into high value chemicals. / Maria Oliviero, Antonio Luca Langellotti, Andrea Donadio, Marco Baselic*, Anna Martello, Paolo Masi (CAISIAL, Università di Napoli Federico II, Portici, NA), Antonino Pollio (Dipartimento di Biologia, Università di Napoli Federico II).

WMV1-P27 C-SERVEES project: development of the Logistic Platform to enable the re-use of WEEE/ Sara Fozza, Marta Speranza, Davide Maglio (RINA Consulting)

WMV1-P28 The innovations in recycling and recovery of materials and energy in management of municipal solid waste in Catania / Elisabetta Chiara, Tommaso Alberto Vazzano, Fausto Scaro, Agata Matarazzo (Department of Economics and Business, University of Catania, Catania, Italy), Franco Corso, Letterio Mario Tringali, Salvatore Fiscella (Department Integrated System of Urban Hygiene, Municipy of Catania, Catania, Italy)

WMV1-P29 Reversible Technologies towards Circular Constructive Products / Tecla Caroli, Andrea Campioli, Monica Lavagna (Dipartimento di Architettura, Ingegneria delle Costruzioni e Ambiente Costruito, Politecnico di Milano)

WMV1-P30 MTR E PEF: novità, scadenze, tooL / Pasquale Lepore (direttore tecnico Officine Sostenibili srl ed Excogito società di ingegneria, componente direttivo PAYT Italia)

WMV1-P31 Troppi ostacoli alla circular economy: per realizzare il PNRR serve un cambio di mentalità / Alessandro Kiniger (B&P Avvocati)

WMV1-P32 Sustainable roads – revamping of asphalt production plants for the compliance to "Circular Economy Package" and "PAN GPP" requirements. / Claudia B. Mosangini, Roger M. Midence, (Ecosurvey®, Bologna), Christian Fontana (Dipartimento di Ingegneria Industriale, Università di Padova)

WMV1-P33 Sistema di Accumulo Energetico Urbano Integrato per Smart City e Mobilità elettrica./ Antonio Caloro (Environ Governance)

WMV1-P34 The circular economy, monitoring and control / Jani Hautaluoma (LNG & Renewable gas, Senior Business Manager, Valmet Automation Inc.)

WMV1-P35 La valorizzazione energetica del rifiuto – l'impianto del COGESA S.p.A. / Stefano Margani, Davide Amadio, Paola Di Iorio, Federica Pantano, Fabrizio Santini (COGESA S.p.A.)

WMV1-P36 Yarrowia lipolytica as a sustainable microbial platform for value added compounds production from Waste Cooking Oils / Antonino Biundo, Mattia Colacicco, Cosetta Ciliberti, Ruggiero Gorgoglione, Gennaro Agrimi, Isabella Pisano (Department of Biosciences, Biotechnology and Biopharmaceutics, University of Bari, Italy)

WMV1-P37 Tecnologie avanzate di upgrading del biogas ai fini della valorizzazione energetica  / Cieri V., Zarra T., Belgiorno V., Naddeo V. (Laboratorio di Ingegneria Sanitaria Ambientale (SEED), Dipartimento di Ingegneria Civile, Università degli Studi di Salerno)

WMV1-P38 Efficient enzymatic degradation of poly(ε-caprolactone) by a commercial lipase / Angela Romano, Antonella Rosato, Grazia Totaro, Giulio Zanaroli, Annamaria Celli, Laura Sisti (Dept. of Civil, Chemical, Environmental and Materials Engineering, Alma Mater Studiorum - University of Bologna, Italy)

WMV1-P39 AGRINNOV - Processi di innovazione per la valorizzazione degli scarti e la riduzione dello spreco alimentare / Roberta Scassa (Università Iuav di Venezia), Daniel Collenzini (Università Iuav di Venezia in partnership con Agricom S.r.l.)

WMV1-P40 Technological innovation applied to the production of customized padel rackets / Antonio Grasso, Annamaria Visco (Engineer Department, University of Messina, Institute of polimers and composite biomaterials, CNR-CT), Giuseppe Abramo (KRC, kateneracingcomposite), Michela Gentile, Agata Matarazzo (Department of economics and business-University of Catania)

WMV1-P41 COMPOSER project - Carbon-fiber reinforced cOMPOsites for Sustainable circular Economy models based on Repair and Remanufacturing for Reuse / Eleonora Manarin, Marco Diani, Marcello Colledani, Gianmarco Griffini (Politecnico di Milano)

WMV1-P42 Gli accumulatori elettrici nel settore automotive, gli impatti sull’ambiente e il rischio sull’uomo / Massimiliano Donia (Auditor di Terza Parte IATF e VDA 6.3), Mastrangelo Pasquale, Grazia Trivisonno, Alessia Donia, Nicandro Nardolilli.

WMV1-P43 Waste valorization to replace fossil-based additives in Hot Mixed Asphalts / Valentina Beghetto, Riccardo Samiolo (Crossing Srl)